###################################################################### Integrated DELL(TM) REMOTE ACCESS CONTROLLER 6 (iDRAC6) Version 1.06 ###################################################################### This document contains updated information about the Integrated Dell Remote Access Controller 6 (iDRAC6). For more information about iDRAC6, including installation and configuration information, see the "Integrated Dell Remote Access Controller 6 (iDRAC6) User's Guide" and the "Dell OpenManage(TM) Server Administrator User's Guide." These documents are located on the Dell Support site at "support.dell.com". ###################################################################### TABLE OF CONTENTS ###################################################################### This file contains the following sections: * Criticality * Minimum Requirements * Release Highlights * Known Issues for iDRAC6 v1.06 * Known Issues for Documentation ###################################################################### CRITICALITY ###################################################################### 1 - This section is intentionally left blank ###################################################################### MINIMUM REQUIREMENTS ###################################################################### The following subsections list operating systems that are compatible with the iDRAC6. ====================================================================== SUPPORTED SYSTEMS ====================================================================== iDRAC6 is supported on the following Dell PowerEdge(TM) systems: * Dell PowerEdge T410 * Dell PowerEdge R410 ====================================================================== SUPPORTED MANAGED SERVER OPERATING SYSTEMS ====================================================================== The iDRAC6 is supported by the following operating systems: * Microsoft(R) Windows Server(R) 2003 family The Windows Server 2003 family includes - Windows Server 2003 R2 (Web, Standard and Enterprise Editions) with SP2 (x86). - Windows Server 2003 R2 (Standard, Enterprise and DataCenter Editions) with SP2 (x64). - Windows Server 2003 (SBS, Standard, and Premium Editions) with SP2. * Microsoft Windows Server 2008 With core (Web, Standard, and Enterprise Editions) (x86) * Microsoft Windows Server 2008 With core (Standard, Enterprise, and DataCenter Editions) (x64) * Microsoft Windows Server 2008 SBS, EBS, Standard, and Premium Editions * SUSE(R) Linux Enterprise Server 10 SP2 * Red Hat(R) Enterprise Linux 4.7 (x86_32, x86_64) * Red Hat Enterprise Linux(R) 5 Update 2 (x86_32, x86_64) * VMware ESX 3.5 Update 4 * VMware ESXi 3.5 Update 4 Flash ====================================================================== SUPPORTED WEB BROWSERS ====================================================================== * Microsoft Internet Explorer(R) 6.0 with SP2 for Windows XP, Windows 2000 Sever, Windows 2000 Professional, Windows 2003 Server Gold, Windows 2003 Server SP1, and Windows 2003 Server SP2 * Microsoft Internet Explorer 7.0 for Windows 2003 Server Gold, Windows 2003 Server SP1, Windows 2003 Server SP2, Windows Server 2008, and Windows Vista(R) * Mozilla Firefox 2.0 on SLES 10 SP1 * Mozilla Firefox 3.0 on Windows 2003 Server Gold, Windows 2003 Server SP1, Windows 2003 Server SP2, Windows 2000 Pro, Windows XP, Windows Server 2008, Windows Vista, RHEL 4 & 5, SLES 9 & 10, SLES 10 SP1 ============================================= FIRMWARE VERSIONS ============================================= * iDRAC6 Firmware Version: 1.06 ###################################################################### RELEASE HIGHLIGHTS (FIRMWARE VERSION 1.06) ###################################################################### * Initial release of iDRAC6 1.06 firmware. iDRAC6 Management Features for the initial release include: * IPv6 support * Enhanced LCD functionality including configuration and menu * Web Services Management (WSMAN) support * Enhanced power management including support for setting power budget thresholds * Smart Card authentication support * Dynamic Domain Name System (DDNS) registration * Remote system management and monitoring using a Web interface, the RACADM command line interface, the SM-CLP command line over a telnet/SSH and serial connection. * Support for Microsoft Active Directory(R) authentication - Centralizes iDRAC user IDs and passwords in Active Directory using the standard schema or an extended schema. * Console Redirection — Provides remote system keyboard, video, and mouse functions. * Virtual Media - Enables a managed server to access a local media drive on the management station or ISO CD/DVD images on a network share. * Monitoring - Provides access to system information and status of components. * Access to system logs - Provides access to the system event log, the iDRAC log, and the last crash screen of the crashed or unresponsive system that is independent of the operating system. * Dell OpenManage(TM) integration - Enables you to launch the iDRAC Web interface from Dell OpenManage Server Administrator or IT Assistant. * iDRAC alert - Alerts you to potential managed node issues through an email message or SNMP trap. * Remote power management - Provides remote power management functions, such as shutdown and reset, from a management console. * Intelligent Platform Management Interface (IPMI) 2.0 support. * Secure Socket Layer (SSL) encryption - Provides secure remote system management through the Web interface. * Password-level security management - Prevents unauthorized access to a remote system. * Role-based authority - Provides assignable permissions for different systems management tasks. NOTE: iDRAC6 Enterprise is required to support dedicated NIC, virtual KVM, virtual media, vFlash (with optional SD card) and RACADM functionality. ###################################################################### KNOWN ISSUES FOR iDRAC6 v1.06 ###################################################################### This section provides additional information about known issues with the iDRAC6 Firmware version 1.06 * Configuring iDRAC to use Static IP using 'syscfg' utility Given below is the method to use the syscfg utility to set the iDRAC to use a static IP address. It has to be done in 2 steps. Step 1: "syscfg lcp --ipaddrsrc=static" Wait for at least 5 seconds. After this time, the change to static IP will be in effect and the next syscfg command will succeed. Step 2: "syscfg lcp --gateway=(gateway IP) --ipaddress=(valid IP address) --subnetmask=255.255.255.0" * Manual Operating System Installation Requirement when using 'virtual floppy' When using vMedia to install an Operating System, the following is required to allow the installation to complete successfully: When installing drivers using a floppy disk, ensure that the Vfloppy device is set as the first device in the Boot sequence in the System BIOS (F2). This will allow the Operating System to see the required mass storage device drivers on the floppy to complete the installation. This way, the drivers in the floppy can be used to install the storage, drivers, and so on and complete the Windows or other installations. * Configuring the 'Host Name String' using the iDRAC Configuration Utility With OMSA installed - OMSA takes precedence. OMSA sets the 'Host Name String' every time it starts up. Given above, even if 'Host Name String' is set using the iDRAC Configuration Utility, it will be overwritten by OMSA when it starts up. With OMSA NOT installed - The iDRAC Configuration Utility can be used to configure the 'Host Name String'. * Accessing remote floppy disks and CD-ROMs from (VMWare) VMs Accessing remote floppy disks and CD-ROMs from (VMWare) VMs is NOT supported. Only devices directly connected to an ESX server or a floppy or CD-ROM ISO image present in the ESX Service Console can be made accessible to the VM. Avoid this issue by creating an image of the floppy or CD-ROM and copying it to the Service Console. * Using the vmcli tool from within a system running Windows Vista To use vmcli from within a system running Windows Vista - The user has to start up the 'cmd' with 'Run as Administrator'. (vmcli requires that the user has administrator' privileges when it is used.) Note - User can log in as a non-admin user, but when using vmcli, the user has to start 'cmd' with 'Run as Administrator' privilege, thereby giving them admin privileges to enable using vmcli. * Avoid uploading the image from multiple management systems to the virtual flash at the same time to prevent image corruption. * The name of the firmware image file for iDRAC6 is firmimg.d6 * If the network cable to iDRAC6 is disconnected and then connected again, iDRAC6 will not negotiate a new IP address until the current lease expires. * Remote Racadm and VMCLI utilities are not supported with IPv6 in this release. * If iDRAC firmware update is interrupted for any reason, a wait of up to 30 minutes may be required before another firmware update operation is allowed. * The Diagnostic tab on the GUI page is not operational if the iDRAC6 - Enterprise card is not installed. * Enabling Virtual Flash from the iDRAC Configuration Utility will not take effect if the SD card is not formatted. Format the SD card from iDRAC GUI or using "racadm vmkey reset" command before enabling it. * In SM-CLP start or stop on the target /system1/ sp1/adsvc1 displays an error “*-* yyerror: syntax error, unexpected ZTOK_PARAMVALUE, expecting XTOK_VALUE or XTOK_VALUEARRAY or XTOK_VALUEREFERENCE” and hangs the telnet/ssh session . It recovers only when the session times out or is restarted. This target is not supported with iDRAC6 firmware 1.01. * You must close an open POST boot capture log video before you play another one. You cannot play two logs simultaneously. * The status for System Board Riser1 Pres and System Board Riser2 Pres sensors is reported incorrectly as unknown instead of good on R710 and R610 servers. * VMDeploy script, vmdeploy.sh, does not work correctly on all supported Linux versions. To fix the issue, modify the following lines in vmdeply.sh using a Linux editor like vi: - Line 198: Replace if [ "`grep \"RAW RSP (0 bytes)\" ipmitool_log`" != "RAW RSP (0 bytes)" ] with grep "RAW RSP (0 bytes)" ipmitool_log if [ "$?" != 0 ] - Line 230: Replace if [ "`grep \"not supported\" ipmitool_log`" != "not supported" ] with grep "not supported" ipmitool_log if [ "$?" != 0 ] ###################################################################### KNOWN ISSUES FOR DOCUMENTATION ###################################################################### This section provides additional information about known issues for documentation with the iDRAC6 Firmware version 1.06 * None ###################################################################### Information in this document is subject to change without notice. (C) 2009 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: "Dell", "OpenManage", and "PowerEdge" are trademarks of Dell Inc.; "Microsoft", "Windows", "Windows Server", "Active Directory" and "Windows Vista" are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries; "Intel" is a trademark of Intel Corporation in the U.S. and other countries; "SUSE" is a registered trademark of Novell, Inc. in the United States and other countries; "Red Hat" and "Red Hat Enterprise Linux" are registered trademarks of Red Hat, Inc. in the United States and other countries. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own. May 2009