Dell SAS 5 and SAS 6 Controller Device Driver for Windows 2003 x86 Version 1.24.04.00 TABLE OF CONTENTS ================= 1.0 Introduction 2.0 Compatibility / Minimum Requirements 3.0 Install Instructions 3.1 Installing the Driver During Operating System Installation 3.2 Installing a Windows Driver for a New SAS Controller 3.3 Updating an Existing Windows Driver 3.4 Driver Update using Dell Update Package (DUP) 4.0 Fixes or Enhancements in this Release 5.0 Additional Information 6.0 Known Issues 1.0 Introduction ================ This is the driver for following controllers: SAS 5 Controllers SAS 6 Controllers 2.0 Compatibility / Minimum Requirements ======================================== This device driver requires the following minimum Operating System version: Windows Server 2003 i386, Service Pack 1 Minimum SAS 5 FW package version: 00.10.51.00.06.12.04.00 Minimum SAS 6 FW package version: 00.20.43.00.06.14.08.00 3.0 Install Instructions ======================== This driver package contains the Windows device driver for the SAS 5 and SAS 6 controllers. To build the installation media these files should be copied to a blank floppy diskette or USB key. 3.1 Installing the Driver during Operating System Installation -------------------------------------------------------------- 1. Power on the system and boot to the Microsoft Windows Server CD. 2. When the message "Press F6 if you need to install a third party SCSI and RAID driver" appears, press the key immediately. Within a few minutes, a screen will appear asking for the driver to support the additional controllers in the system. 3. Press the key. The system prompts for the driver diskette to be inserted. 4. Insert the driver diskette in the floppy drive (or the USB key in the USB port) and press the key. A list of SAS drivers will appear. 5. Select the appropriate driver for the installed controller and OS and press the key to load the driver. 6. Press the again key again to continue the installation process. 3.2 Installing a Windows Driver for a New SAS Controller -------------------------------------------------------- Perform the following steps to configure the driver when you add a new controller to a system that already has Windows installed. 1. Power down the system. 2. Install the new SAS controller in the system. Refer to Hardware Installation for detailed instructions on installing and cabling the SAS controller in the system. 3. Power on the system. The Windows operating system should detect the new controller and display a message to inform the user. 4. The Found New Hardware Wizard screen will pop up and display the detected hardware device. 5. Click on Next. 6. On the Locate Device Driver screen, select Search for a suitable driver for my device and click on Next. 7. Insert the appropriate driver diskette or USB key and select that device on the Locate Driver Files screen. 8. Click on Next. 9. The wizard detects and installs the appropriate device drivers for the new controller. 10.Click on Finish to complete the installation. 11.Reboot the system. 3.3 Updating an Existing Windows Driver --------------------------------------- Perform the following steps to update the Windows driver for a new controller already installed on your system. NOTE: It is important that you put your system on idle before you update the driver. 1. Press Start > Control Panel > System. The System Properties screen will be displayed. 2. Click on the Hardware tab. 3. Click on Device Manager and the Device Manager screen will be displayed. 4. Click on SCSI and RAID Controllers. 5. Double-click on the controller for which you want to update the driver. 6. Click on the Driver tab and click on Update Driver. The Upgrade Device Driver Wizard will be displayed. 7. Insert the appropriate driver diskette or USB key. NOTE: The driver files can also be copied to the hard drive. 8. Click on Next. 9. Follow the steps in the Wizard to browse for the new driver. 10.Select the driver. 11.Click on Next and continue the installation steps in the Wizard. 12.Click on Finish to exit the wizard and reboot the system for the changes to take effect. 3.4 Driver Update using Dell Update Package (DUP) -------------------------------------------------- A Dell Update Package (DUP) is a self-contained executable in a standard Dell package format and each Update Package is designed to update a single component on your system. DUP Download ------------ 1. Click the Download Now link to download the file. 2. When the File Download window appears, click Save to save the file to your hard drive. Driver Update ------------- 1. Browse to the location where you downloaded the file and double-click the new file. 2. Read over the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update. Silent Driver Update -------------------- Execute the DUP from the command line (or script) as follow: > DRVR_WIN_Rxxxxxx.exe /s /l= /r Where: /s Executes the update silently without user intervention. /r Reboots the system, if required, after performing the update. /l= Appends logged messages to a specified ASCII file; creates a new file if one does not exist. For more command line options type > DRVR_WIN_Rxxxxxx.exe /? or consult the "Dell Update Package User's Guide". 4.0 Fixes or Enhancements in this Release ========================================= - Added the correct SAS 6/iR Device names: "Dell SAS 6/iR Adapter Controller" "Dell SAS 6/iR Integrated Blades Controller" "Dell SAS 6/iR Integrated Controller" "Dell SAS 6/iR Integrated Workstation Controller" 5.0 Additional Information ========================== The Driver version may be displayed in a different manner depending on the application because the leading zeros are often trimmed and not shown. (i.e.: 1.24.04.00 will sometimes be displayed as 1.24.4.0). 6.0 Known Issues ================ None.